TYPEWRITER: Replacing The Drawcord On A Remington Portable.

The machine used in this article is a 1924 Remington Portable #1, but the drawcord mechanics are the same on the Portable #2 and #3, so, let’s start:

I’ve replaced several drawcords on different Remington Portables. Below is my method (not the method) for replacing the broken cord with a new cord. What you need is:

  • a magnetic rod to ‘lock’ the main spring, I use a flashlight with a magnetic bottom,
  • a cord to serve as a drawcord. I use thin black woven cord intended for venetian blinds,
  • a piece of wire to finagle the cord through the holes in the main spring. I use a dental hook for that,
  • a sharp screwdriver,
  • a thin wooden/bamboo stick, I use a ‘saté stick’ for skewering meat, but as long as it’s thin and about 20cm long (like a thin crocheting hook/needle), it will do,
  • A soft cushion to put the machine on, I use a piece of foam.

First, put the Remington Portable upside down on the cushion with the carriage close to you. Holding the magnetic rod handy, you start winding up the spring in the main spring housing so it nestles tightly against the axle and the small round hole is exposed, then place the magnetic rod on the mainspring housing so it stays in position.

Main spring tightly wound and kept in place with magnetic rod.
Broken piece of cord visible in the hole.

Use the dental hook to fish the cord from the hole.

Broken piece of cord removed.

When you have removed the piece of cord, put a new piece of cord through the side into the main housing and pull it up through the hole.

New cord inserted through the side and out of the hole.

Tie a tight knot in the short part that comes out of the hole and pull the cord to push that knot into the hole next to the coiled spring.

Tight knot. If it’s nylon, you can heat it up with a lighter to melt the fluff.
The knot pushed into the hole next to the coiled spring.

Remove the magnetic lock and slowly let the spring in the main housing uncoil and press up against the knot. When the spring uncoils, keep the cord up so it won’t catch under the mainspring housing. When the spring is totally uncoiled, you wind up the housing 4 rotations. This is more than enough to pull the carriage. Lock the mainspring housing with the magnetic rod again. The hole with the cord coming out is at your side, the side of the carriage.

Mainspring housing rotated 4 times and locked, with the drawcord towards the carriage.

Pull the carriage all the way to your right (fully extended carriage), and lead the cord around the tiny pulley and hook the cord under the guide hook.

Around the pulley and hook the cord through the guide from below.
View of the pulley and guide hook with cord running through.

Tape the end of the cord to a stick to thread the cord underneath the carriage. Make sure the cord travels straight under the carriage (over the carriage now that the machine is upended, of course) to the far end.

Tape the end of the cord to a stick.
Guide the cord to the other side of the carriage.
This is the part you lightly unscrew, so you can remove the part that holds the end of the cord.
And this is the part that hooks behind the screw to clamp on the end of your drawcord.

The drawcord is pulled taut and clamped between the carriage and that little brass hook, screwed down tightly. Originally, the cord is clamped inside that little brass thingy, but that folded brass part is difficult to unfold and might break. So I hold the cord against the carriage over the screw, push the brass hook into position behind the screw and tight the screw.

Drawcord clamped behind the brass hook and screw tightened.

When you are sure the cord is tightly clamped, add a knot to the end for security.

The knot might not be necessary, but who cares?

And your Remington Portable is ready for use again!

1924 Remington Portable #1 with the typebars in the resting position.
1924 Remington Portable #1 with the typebars in the raised position.